SunMan Engineering, Inc

"The Product Engineering, Layout and Prototyping Specialist" Since 1990

Phone: 1(408)441-1500

PCB Glossary

Active Components: Semiconductor devices, such as transistors and diodes, that can change its basic characteristics in an powered electrical circuit, such as amplifiers and rectifiers.

Analog Circuit: An electrical circuit that provides a continuous quantitative output as a response from its input.

Annular Ring: The width of the conductor pad surrounding a drilled hole.

Artwork: Printed circuit design.

Aspect Ratio: The ratio of the board thickness to the smallest-hole diameter of the printed circuit board.

Assembly File: A drawing describing the locations of components on a PCB.

Automated Test Equipment (ATE): Equipment that automatically tests and analyzes functional parameters to evaluate performance of the tested electronic devices.

Ball Grid Array (BGA): A SMD package in which solder ball interconnects cover the bottom surface of the package.

Bare Board: An unpopulated PCB.

Base Copper Weight: see Copper Foil

BBT: Bare Board Test.

Bill of materials (BOM): A comprehensive listing of all subassemblies, components, and raw materials that go into a parent assembly, showing the quantity of each required to make the assembly.

Built-In Self Test: An electrical testing method that allows the tested devices to test itself with specific added-on hardware.

CAD: Computer Aided Design.

CAM: Computer Aided Manufacturing.

CAM Files: The files used for manufacturing PCB including Gerber file, NC Drill file and Assembly Drawings.

Ceramic Ball Grid Array (CBGA): A ball grid array package with a ceramic substrate.

Chip-on-Board (COB): A configuration in which a chip is directly attached to a printed circuit board or substrate by solder or conductive adhesives.

Chip: The individual circuit or component of a silicon wafer, the leadless form of an electronic component.

Component Side: The Side of a PCB on which most of components are mounted.

Coating: A thin layer of material, conductive, magnetic or dielectric, deposited on a substance surface.

Coefficient of Thermal Expansion (CTE): The ratio of dimensional change of an object to the original dimension when temperature changes, expressed in %/ºC or ppm/ºC.

Contact Angle (Wetting Angle): The angle between the contact surfaces of two objects when bonding. The contact angle is determined by the physical and chemical properties of these two materials.

Copper Foil (Base Copper Weight): Coated copper layer on the board. It can either be characterized by weight or thickness of the coated copper layer. For instance, 0.5, 1 and 2 ounces per square foot are equivalent to 18, 35 and 70 um-thick copper layers.

Corrosive Flux: A flux that contains corrosive chemicals such as halides, amines, inorganic or organic acids that can cause oxidation of copper or tin conductors.

Curing: The irreversible process of polymerizing a thermosetting epoxy in a temperature-time profile.

Curing Time: The time needed to complete curing of an epoxy at a certain temperature.

DFSM: Dry Film Solder Mask.

Die: Integrated circuit chip as diced or cut from a finished wafer.

Die Bonder: The placement machine bonding IC chips onto achip-on-board substrate.

Die Bonding: The attachment of an IC chip to a substrate.

Dielectric: An insulating medium between conductors.

DIP: Dual in-line package with two rows of leads from the base in standard spacing between the leads and row. DIP is a through-hole mounting package.

Double-Sided Assembly: PCB assembly with components on both sides of the substrate.

DRC: Design rule check.

Dry - Film Resists: Coated photosensitive film on the copper foil of PCB using photographic methods. They are resistant to electroplating and etching processes in the manufacturing process of PCB.

Edge Connector: A connector on the circuit-board edge in the form of gold plated pads or lines of coated holes used to connect other circuit board or electronic device.

Edge Clearance: The smallest distance from any conductors or components to the edge of the PCB.

Electroless Deposition: The chemical coating of a conductive material onto a base material surface by reduction of metal ions in a chemical solution without using electrodes compared to electroplating.

Electroplating: The electrochemical deposition of reduced metal ions from an electrolytic solution onto the cathode by applying a DC current through the electrolytic solution between two electrodes, cathode and anode, respectively.

ESR: Electro-statically applied Solder Resist.

Fine Pitch: Fine pitch is more commonly referred to surface-mount components with a lead pitch of 25 mils or less.

Finger —A gold-plated terminal of a card-edge connector. Also see Gold Finger.

Flux: The material used to remove oxides from metal surfaces and enable wetting of the metal with solder.

FR4: Flame Retardent laminate made from woven glass fiber material impregnated with epoxy resin.

Functional Test: The electrical testing of an assembled electronic device with simulated function generated by the test hardware and software.

Gerber File: Data file used to control a photoplotter.

Ground Plane: A conductive plane as a common ground reference in a multilayer PCB for current returns of the circuit elements and shielding.

GI: The woven glass fiber laminate impregnated with polyimide resin.

Gold Finger —The gold-plated terminal of a card-edge connector. Also see Finger.

HDI: High Density Interconnect.

Hermetic: Airtight sealing of an object.

In-Circuit Test: Electrical test of individual component or part of the circuit in a PCB assembly instead of testing the whole circuit.

Hole Density: The number of holes per unit area on a PCB.

Interstitial Via Hole: An embedded through-hole with connection of two or more conductor layers in a multilayer PCB.

Laminate: A composite material made by bonding together several layers of same or different materials.

Lamination: The process manufacturing a laminate using pressure and heat.

Leakage Current: A small amount of current that flows across a dielectric area between two adjacent conductors.

Legend: A format of printed letters or symbols on the PCB, such as part numbers and product number or logos.

LPI: Liquid Photo-Imageable solder mask that uses photographic imaging to control a thinner mask deposition than the dry film solder mask.

Minimum Conductor Width: The smallest width of any conductors, such as traces, on a PCB.

Minimum Conductor Space: The smallest distance between any two adjacent conductors, such as traces, in a PCB.

Multilayer PCB: Circuit boards consisting three or more layers of printed circuits separated by laminate layers and bonded together with internal and external interconnections.

NC Drill: Numeric Control drill machine used to drill holes at exact locations of a PCB specified in NC Drill File.

Netlist: List of parts and their connection points which are connected in each net of a circuit.

Node: A pin or lead to which at least two components are connected through condcutors.

NPTH: Non-plated trough-hole.

Pad: The portion of a conductive pattern for connection and attachment of electronic components on the PCB. Also called Land.

PCB: Printed Circuit Board. Also called Printed Wiring Board (PWB).

PCMCIA: Personal Computer Memory Card International Association.

PEC: Printed Electronic Component.

Pick-and-Place: A manufacturing operation of assembly process in which components are selected and placed onto specific locations according to the assembly file of the circuit.

Pitch: The center-to-center spacing between conductors, such as pads and pins, on a PCB.

Plastic Leaded Chip Carrier (PLCC): A component package with J-leads.

PTH (plated-through Hole): A plated hole used as a conducting interconnection between different layers or sides of a PCB either used as connection for through-hole component or as a via.

Plating Resist: Material deposited as a covering film on an area to prevent plating on this area.

Reflow Soldering: Melting, joining and solidification of two coated metal layers by application of heat to the surface and predeposited solder paste.

Resist: Coating material used to mask or to protect selected areas of a pattern from the action of an etchant, solder, or plating.

Route (or Track): A layout or wiring of an electrical connection.

RF (radio frequency) and wireless design: A circuit design that operates in a range of electromagnetic frequencies above the audio range and below visible light. All broadcast transmission, from AM radio to satellites, falls into this range, which is between 30KHz and 300GHz.

Screen Printing: A process for transferring an image from a patterned screen to a substrate through a paste forced by a squeegee of a screen printer.

Silk Screen (Silk Legend): Epoxy-ink Legend printed on PCB. The most common colors used are white and yellow.

Small Outline Integrated Circuit (SOIC): An integrated circuit with two parallel rows of pins in surface mount package.

SMOBC: Solder mask over bare copper.

SMD: Surface Mount Device.

SMT: Surface Mount Technology.

Solder Bridging: Solder connecting, in most cases, misconnecting, two or more adjacent pads that come into contact to form a conductive path.

Solder Bumps: Round solder balls bonded to the pads of components used in face-down bonding techniques.

Solder Mask or Solder resist: Coating to prevent solder to deposit on.

Solder Wick: A band of wire removes molten solder away from a solder joining or a solder bridge or just for desoldering.

Temperature Coefficient (TC): The ratio of a quantity change of an electrical parameter, such as resistance or capacitance, of an electronic component to the original value when temperature changes, expressed in %/ºC or ppm/ºC.

Test Point: A specific point in a circuit board used for specific testing for functional adjustment or quality test in the circuit-based device.

Testing : A method for determining whether sub-assemblies, assemblies and/or a finished product conform to a set of parameter and functional specifications. Test types include: in-circuit, functional, system-level, reliability, environmental.

Turnkey: A type of outsourcing method that turns over to the subcontractor all aspects of manufacturing including material acquisition, assembly and testing. Its opposite is consignment, where the outsourcing company provides all materials required for the products and the subcontractor provides only assembly equipment and labor.

UL: Underwriter’s Laboratories. A popular safety standard for electrical devices supported by many underwriters.

Via: A plated-through hole used for interconnection of conductors on different sides or layers of a PCB.

Wave Soldering: A manufacturing operation in which solder joints are soldered simultaneously using a wave of molten solder.